The basic set is one of the most versatile baits a bass angler can have in their arsenal. It can be fished in almost any way, at any depth, and around most types of cover and structure. In some ways, however, a stencil is one of the most complex lures, as every detail can be fine-tuned to best suit a variety of situations. Because of the adaptability of the template, bass anglers have developed custom styles over time to handle specific techniques.
As you learn more about fishing tackle, you will appreciate the benefits of each of these styles.
1. Swimming gauge
How to fish it: The swimming gauge is designed for grass and wood, but can also be bitten in open water. Just don’t pull it. Swim it. Sometimes a straight retrieval is desirable, but another common technique is to shake the pole tip as it is rolled up. It can be fished right on the surface, scratching the bottom or in between.
Size selection: 3/16 to 1/2 ounce for flat presentations; 3/4 ounce and heavier for slow rolling in deep water or blowing through heavy grass.
– Use white or silver colors when mimicking shadows and combinations of green, brown, purple, and orange when mimicking bluegills.
– A swimming gauge should have a reliable bait holder – either a large lead barb or metal wire – to hold the trailer in place.
– Cut the skirt so short that it does not hang over the moving parts of the trailer.
2. Football device
How to fish it: Thanks to its head shape, football theory is the king of deep sea fishing. It is designed in such a way that it does not tip over if it is pulled onto the floor on ledges, points and the like. It’s also a great tool for feeling the content below. To fish it just pull the template along a little, take off the slack and repeat the process. Before you hook the line, wind up the line. A soccer stencil can also be stroked up and down from below.
The technique: Rip it up, then let it sink back on a loose or semi-loose leash. Fish usually bite in the fall.
Size selection: 1/2 to 1 ounce for most situations; 1 1/4 and 1 1/2 ounces for extreme depths.
– Unless you are fishing near brushes or wooden covers, you should thin out the weed protection. This can help to improve the connection ratio.
3. Tilting device
How to fish it: The design of the flip jigs is very different. Part of this is due to the variety of types of lids that anglers flip and the fact that some devices are designed to be versatile enough for other techniques. Typically, a flip jig is a target bait for short flips, pitches, and roll-casts on flat wood, coastal grass, deeper grass beds (in some situations), and docks. Once the bait hits its target, drop it, hop a time or two, then reel it back in for the next flip. Shoot each time for a smooth entry into the water.
Size selection: 3/8 to 3/4 ounce
– The fall rate can be critical when turning over. Adjust the rate of fall by changing the size of the jighead, the thickness and length of the apron, and the style of the pendant. The more compact the package, the faster it will sink. Leave the rock full to slow the rate of descent.
4. Punching jig
How to fish it: A punching device is a special tilting device designed to break through matted grass. It’s also a great option for turning over deep, submerged grass, a thick wooden ceiling, or when you want a really bulky, fast-sinking presentation. Sometimes it is necessary to lift the stencil in the air so that it can build up a certain speed in the fall to get through the grass. In most cases, a punch gauge should be fished with a braid that can cut through blades of grass and turn a fish into thick cover.
Size selection: 3/4 to 2 ounces
– Some punches have double weed guards for even more deflection.
– Compact trailers without many “rickety” attachments slide through the cover more easily than bulky trailers.
5. Finesse Jig
How to fish it: The technique depends on the scenario, but a finesse stencil can be targeted, dragged, skipped under cover, or bombed over the structure. The key is to fish it very slowly, usually with soft tugs or short lifts of the top of the rod.
Size selection: 3/16 to 3/8 ounce
– Tungsten is a good choice for a finesse device.
– To cut a skirt with a spider, pull the front half of the strands over your head, hold them together, and cut the strands right in front of your head.
– In cold water, round strands of rubber skirt are sometimes preferred because they flicker and pulsate even when the jig is barely moving.
6. Casting / structure device
How to fish it: The cast / structure jig is the basic general purpose jig that can be skipped, tilted, or flipped over. However, it is great for pulling presentations on sloping rocky banks, plains, points, and other structures of medium depth. One key is that the template be compact enough that a bass can easily suck it off the floor. But more importantly, it needs a head design that will allow it to crawl over rocks without getting caught. As a result, most of them have a flat floor, e.g. B. an Arkie style stencil or the newer structural style head that resembles a crushed soccer ball. Some are pointed and resemble arrowheads. Using short tugs or a lift-drop technique, drag the stencil along the floor.
Size selection: 3/16 to 5/8 ounces
– Try shortening the skirt by turning the template upside down and using scissors to cut diagonally across the strands. The result is a wide range of strand lengths and a vibrant apron.
To learn firsthand about fishing tackle and techniques from seasoned FLW anglers, visit the #ReelFun Fishing Events held at Walmart stores across the United States from June 2-4, 2017. You can find dates and times on TakeMeFishing.org
Curtis Niedermier is currently the Editor-in-Chief of FLW Bass Fishing Magazine
This article was originally published on FLWFishing.com.
Curtis Niedermier is Editor-in-Chief of FLWFishing.com and FLW Bass Fishing magazine. He has covered the professional fishing rounds for 10 years.